中文
ENGLISH
中文
ENGLISH
Die casting aluminum process is a versatile process. It allows the creation of complex, yet robust and efficient shapes. Aluminium itself is a great alloy for prototype and product creation. The popularity of the material has led to a number of casting techniques.
Each of these techniques offers different benefits. At the same time, they do come with their limitation. However, it is important for every type of casting to yield great results. In this article, we are going to talk about the different aluminum shaping methods.
So, without any further delay, let us get started!
The most common aluminum shaping processes include the following
For any type of metal, casting is the most versatile and effective forming process. It is possible to create some of the best, robust and sturdy parts using this technique. According to the US Department of Energy estimates, roughly 90 percent of the manufactured things have the metal cast products.
You can apply the same casting technique for aluminum that you would use for other metals. But the most common methods include the Die Casting, Green Sand Casting, and the permanent Mold Casting.
Permanent vowin.cn/' target='_blank'>mold casting is among the most common technique for vowin.cn/en/News/news1251.html' target='_blank'>molding metals. It creates a reusable metal mold at an extremely high temperature. When the manufacturer wants to cast-aluminum the mold either should be of steel or gray iron.
The molds two halves are first connected and then they are pre-heated. Once they reach a certain temperature, then its time to pour the molten metal. The metal enters the mold via a ladle. Once the mold is full, give it some time to set and solidify.
After it solidifies, remove it. It is important to take the casting out of the mold as soon as it solidifies as the inflexible mold can result in defects in the casting. After removing the casting, the process is repeated instantly.
It is possible to recoup the initial tooling cost because of the mold’s reusability. Manufacturers are able to generate high-volume runs using the same mold over and over again.
You do not need of preparation between casting.
The technique offers a high repeatability rate.
With permanent casting, it is possible to achieve high dimensional accuracy. However, for accuracy, you need to have accurately machined mold.
The initial tooling cast is fairly high especially when you compare it to other casting techniques.
The molds are inflexible. Thus, it can lead to defects in casting if they are not removed on time.
In the case of large runs, you may have to replace the permanent mold as they have a short lifespan.
Another effective technique for casting aluminum is the Greensand casting. The technique uses clay-bounded, moist sand to create the mold. The first step to packing sand around the desired pattern in order to create the mold cavity.
After that, it is time to remove the pattern. Then, the manufacturer places the mold into a brace. At this stage, the cavity is paired with its other half. This part is similar to that of the permanent mold casting. Once the mold is ready, it is time to pour the molten metal into the cavity.
Now, wait for the casting to solidify. In order to remove the casting, the manufacturer breaks the mold. This step is different from the permanent molding, where, it is possible to reuse the mold. To finish off the casting process, grind the needless features such as the risers and tabs.
Most facilities are able to reuse most of the sand used in this casting process.
The technique offers diversity in terms of size and weight. It is possible to cast almost any part using Greensand casting.
Both the material and the tooling cost is extremely low.
Every time, you would need a new mold as the process requires to break the previous mold to remove the casting.
The casting surface is not very smooth. You might have to do some additional work on it.
The technique does not offer dimensional accuracy.
The die casting Aluminium process is similar to that of the permanent casting. Both these techniques reuse the metal mold instead of disposing of the mold as it is the case in Greensand casting. In die casting, the molten metal injection takes place at high temperatures.
Due to the high pressure, the casting is able to have a better surface finish and it has greater details. However, if not being careful, the injection can lead to a trapped pocket of air. This would have an adverse impact on the durability of the die casting.
Manufacturers would recommend die casting aluminium for mass production of small size parts.
NOTE: The complexity of the process is limited.
Due to the configuration of the die casting apparatus, the manufacturers have limited choices in terms of cores. As the configuration does not allow a variety of cores to be inserted.
With die casting it is possible to cast parts that have superior detailing and surface finish.
Dies that are created using high-grade tool steel have a longer life. They are robust and sturdy.
The technique offers limited complexity especially when the products have hollow sections.
The initial tooling cost is extremely high.
The strength of the mold can be compromised due to defects such as porosity.
| Labor Cost | Initial Cost | Typical Tolerances | Typical Volume | Surface Finish | |
| Permanent Mold | Low | High | +/- .01 — .03 in. | Medium-High | Good |
| Die | Low | Very High | +/- .01 — .015 in. | Very High | Very Good |
| Greensand | Low | Low | +/.01 — .06 in. | Low-High | Average |
There are different methods for casting aluminum, but the most common one is the die casting aluminium technique. This method is highly effective and efficient. It yields projects that do not require additional work after being cast.
Although the initial tooling cost is high, it is possible to reuse the molds. Thus, this is compensation in terms of cost. What more is that the technique has a low labor cost and great tolerance.
We offer the best die casting services. Reach out to us today and learn more about our services.
